Turbulent Sky
Tech Tips, Tricks and Solutions

by

Do you have a Samsung Epic 4G or other Android phone? Do you have to recharge your battery daily or more than once a day even when you’re hardly doing anything with it? That’s not normal. My Samsung Epic, when lightly used, only needs to be recharged every three to four days.

“Impossible!” you say. “These are powerful phones and they use up the battery faster.” That may be true if you’re talking on the phone, watching videos and playing Angry Birds on it all day long. However, many people are having to frequently recharge their phones even under light to no usage, which should not be happening.

“You must use task killers, Juice Defender, a special kernel or some extreme tools to get that kind of battery life.” Actually, I’ve tried some, but abandoned such measures. They’re not necessary. There are many well-known ways to conserve power such as turning off services you don’t need, checking for mail less often, dimming the screen, etc. These are certainly important and should be practiced. But, there’s more.

Despite these normal power conservation techniques, when the Samsung Epic starts to drain the battery, it does so at an alarming rate. Here’s a log of the battery level at approximately ten-minute intervals that I kept when mine recently started to suck the battery dry:

62% @ 11:37 pm
61% @ 11:45 pm
59% @ 11:58 pm
57% @ 12:10 pm
56% @ 12:17 pm
55% @ 12:27 pm
52% @ 12:37 pm
51% @ 12:47 pm
50% @ 12:57 pm
49% @ 1:07 am
48% @ 1:10 am
47% @ 1:20 am
45% @ 1:36 am
44% @ 1:50 am
43% @ 2:05 am

It’s draining the battery at a rate of about 10% per hour. This is with the phone’s screen, GPS, 3G/4G data, Wi-Fi, automatic updates, Bluetooth and sound turned off. No applications were running. In fact, during this period, I had more things turned off than I usually do.

It’s been documented at the Sprint Community forum and various blogs that the Samsung Epic can go into a mode where it will continuously search for the cellular network. I have encountered this and the usual fix is to turn on airplane mode for a few seconds and then turn it off again to reset the radio. Unfortunately, I found that this fix doesn’t always work. Even shutting down the phone completely and then turning airplane mode on and off doesn’t help.

In the two cases thus far, when the simple fix for this problem didn’t work, two things did. The first was turning on airplane mode overnight. The second was turning the phone completely off overnight. Here’s a short log of battery life after the overnight fix for the sudden battery consumption I logged above:

41% @ 8:33 am
41% @ 8:44 am
41% @ 8:49 am
41% @ 9:00 am
40% @ 9:01 am
40% @ 9:10 am
40% @ 9:20 am
40% @ 9:33 am
39% @ 9:41 am

As you can see, now the phone is only consuming 1-2% per hour, rather than 1% every 10 minutes. The screen was off, but 3D data was enabled and some services that I turned off during the excessive battery usage were running again since the phone had freshly booted. So, despite having more things turned on, the phone is back to normal and will last significantly longer than the 8-10 hours that many owners of the Samsung Epic are reporting online as “normal”.

Does this fix really require turning the phone off (or putting it into airplane mode) all night? At this time, I’m not sure how long it needs to stay in the off/airplane state. It definitely needs more than a few minutes, because I’ve tried that and it’s not enough. So, it’s somewhere between a few minutes and 6.5 hours.

Have you tried this fix? How long did you have to keep your phone off or in airplane mode to get it to behave? Post your experience in the comments.

Post a comment

by

I recently ran into a situation where a Linksys WRT-54G wasn’t able to get an IP address when connected to an Ambit/uBee U10C018 cable modem. This issue may also apply to other routers when used with the U10C018 cable modem.

When a PC is connected directly to the modem, everything works fine and the Internet can be reached normally. When a router is placed inbetween, then there is no longer any access to the Internet. Viewing the status information in the router shows that it is unable to acquire an IP address, even though the router is set to use automatic configuration via DHCP, the same as the PC.

Apparently, the U10C018 cable modem is aware of the MAC address of various routers. In order to get the router to work with the modem, use the MAC cloning feature of the router. The location of this option will depend on your particular router brand and model. When you find it, turn it on. Then, set the desired MAC address.

On the Linksys router, the MAC address cloning page has a button to copy the MAC from the PC that’s currently connected to the administration interface. If your router has this feature, use it to set the router to the same MAC address as your computer. If your router does not have this feature, then you’ll have to get your MAC from the network driver or the network card.

Once you have a non-router MAC entered into the MAC cloning setting, save and restart the router.

Have you run into this issue? If so, post your router model and steps to configure MAC cloning for it in the comments.

Post a comment


Creative Commons License This work by Peter Ridge is licensed under a Creative Commons Attribution-Noncommercial-No Derivative Works 3.0 License.
Turbulent Sky Theme by Peter Ridge, based on BlueMod Theme by FrederikM.de